基于蜻蜓翅脉结构的连续碳纤维增强树脂基复合材料仿生设计与增材制造

以具有轻质高强优异性能的蜻蜓翅脉结构为设计灵感，在分析翅脉网格结构抗冲击原理的基础上，设计了传统和仿生两类对比结构。采用熔融挤出3D打印机成功制备了具有不同结构的连续碳纤维增强聚乳酸复合材料试样，并对不同结构复合材料试样的拉伸性能和抗冲击性能进行了测试和对比分析。研究分析结果表明：由于拉伸力方向上的连续碳纤维含量相对较少，限制了仿生结构复合材料抗拉强度的提高，但仿生结构的平均抗拉强度为传统结构的1.18倍；当仿生结构复合材料试样受到冲击力时，其内部六边形结构的连接角度会发生变化，从而极大消耗冲击能量，同时具有六边形网格结构的连续碳纤维可以有效阻碍裂纹的扩展，因此仿生结构的平均冲击韧性可以达到传统结构的2.46倍；仿生蜻蜓翅脉结构可以显著提高增材制造复合材料的综合力学性能，且对于抗冲击性能的提高具体突出效果。连续碳纤维增强树脂基复合材料的有效可行的仿生蜻蜓翅脉结构设计和增材制造，可极大扩展其在高冲击载荷领域中的相应应用。     

Enhanced hydrogen production from water splitting by Sn-doped ZnO/BiOCl photocatalysts and Eosin Y sensitization

The construction of semiconductor heterojunction for photocatalytic H₂ production from water splitting is an efficient and environment-friendly technology. In this work, ZnO/BiOCl (ZBC) and Sn-doped ZnO/BiOCl (ZBC-S) photocatalysts with Z-scheme heterojunction were successfully prepared by simple hydrothermal method. The photocatalytic H₂ evolution from water splitting by the as-prepared photocatalysts was investigated. The formation of ZnO/BiOCl heterojunction reduces the recombination probability of the photogenerated carriers. The impurity levels originated from Sn doping reduce the band gap width of ZnO and BiOCl to some extent, thereby enhancing the light absorption ability. The ZBC-S composite exhibits the best photocatalytic activity. In addition, the photocatalytic efficiency of H₂ production was improved by sensitization with Eosin Y (EY) dye. The H₂ production rate under simulated sunlight reaches 4146.77 μmol g^?1 h^?1, which is 27 times higher than that of pure ZnO. Finally, the Z-scheme electron transfer route in ZnO/BiOCl heterojunction was determined, and the photocatalytic H₂ production mechanism of EY sensitized ZBC-S was proposed.     

Hydrogen production performance of a photovoltaic thermal system coupled with a proton exchange membrane electrolysis cell

As one of the cleanest energies, hydrogen has attracted much attention over the past decade. Hydrogen can be produced using water electrolysis in a Proton Exchange Membrane Electrolysis Cell (PEMEC). In the present study, the performance of the PEMEC, powered by the Photovoltaic-Thermal (PVT) system, is scrutinized. It is considered that the PVT system provides the required electrical power of the PEMEC and preheats the feedwater. A comprehensive numerical model of the coupled PVT-PEMEC system is developed. The model is used to investigate the effect of various operating parameters, including solar radiation intensity, inlet feedwater temperature, and feedwater mass flow rate, on the hydrogen production and operating voltage of the PEMEC at various Exchange Current Densities (ECDs). Furthermore, the effect of integration of Phase Change Material (PCM) and Thermoelectric Generator (TEG) on the hydrogen production of the system is evaluated. According to the obtained results, the PVT-TEG-PEMEC system outperforms other systems in hydrogen production. However, integration of the PVT-PEMEC system with PCM has a negligible effect on its hydrogen production.     

A survey on tracking control of unmanned underwater vehicles: Experiments-based approach

This paper aims to provide a review of the conceptual design and theoretical framework of the main control schemes proposed in the literature for unmanned underwater vehicles (UUVs). Additionally, the objective of the paper is not only to present an overview of the recent control architectures validated on UUVs but also to give detailed experimental-based comparative studies of the proposed control schemes. To this end, the main control schemes, including proportional–integral–derivative (PID) based, sliding mode control (SMC) based, adaptive based, observation-based, model predictive control (MPC) based, combined control techniques, are revisited in order to consolidate the principal efforts made in the last two decades by the automatic control community in the field. Besides implementing some key tracking control schemes from the classification mentioned above on Leonard UUV, several real-time experimental scenarios are tested, under different operating conditions, to evaluate and compare the efficiency of the selected tracking control schemes. Furthermore, we point out potential investigation gaps and future research trends at the end of this survey.     

Effects of alkali metal ion on imprinting GRIN microstructure in GeS2-Ga2S3-MCl (M=Na,K, Cs) glasses for visible to mid-infrared microgratings

Gradient refractive index (GRIN) micro-optics present unique opportunities for control of the chromatic properties, new degrees of freedom for optical design as well as the potential for use in new optical system applications. GRIN microgratings were imprinted in GeS₂-Ga₂S₃-MCl (M = Na, K, Cs) chalcohalide glasses by microthermal poling, and the effects of the type and concentration of alkali cations on their performance were investigated. Two effective imprinting formation regions of the GRIN microstructure based on the poling saturation voltage (U_s) and glass composition are observed at fixed poling time and temperature. The U_s increases from 140 to 750 and 2600 V in accordance with the activation energy (E_a) of alkali ions (Na⁺ to K⁺ and Cs⁺) increasing from 45.15 to 58.62 and 92.58 kJ/mol for studied samples. The saturated numbers of diffraction order (N_s) of the gratings in these samples are 7, 9 and 6, respectively, the highest number being provided by the K⁺-containing sample. This is in accordance with imprinting-induced phase differences (0.14λ, 0.19λ and 0.09λ) measured in the fabricated samples containing Na⁺, K⁺ and Cs⁺ ions. Furthermore, the U_s of samples decreases from 1500 to 300 V with four concentrations of K⁺ from 10 to 30%, associated with their E_a of K⁺ decreasing from 69.62 to 53.46 kJ/mol, while N_s increases from 8 to 14, which is attributed to the increase of the phase difference in the GRIN structures. The controllable GRIN microstructures are realized by adjusting the type and concentration of alkali cations in chalcohalide glasses, which is expected to drive the design of broadband GRIN microgratings.     

Spark plasma sintering of UO2 nanopowders: Pressure,heating rate and current effects

We analysed with different methods the densification of UO₂ nanopowders in SPS under constant heating rate (CHR) and isothermal sintering conditions. The apparent activation energy of densification in SPS (75 kJ/mol with CHR method) is significantly smaller than in conventional sintering. It is shown that this is likely not an effect of the applied current. We also observed a threshold stress at 64 MPa for the transition from pressure-insensitive sintering (stress exponent n≈0) to pressure-assisted sintering, suggesting that the contribution of the capillary stresses in such nanopowders is comparable with the typical stress applied in SPS.     

Molecular design for thermally stable SiZrBOC structure from single source precursor with high ceramic yield

A new type of high-temperature-resistant SiZrBOC ceramics was prepared by sol-gel method using polymethyl-hydro siloxane (PMHS), boric acid (B(OH)₃), and n-propyl zirconate (Zr(OPr)₄) as raw materials. After high-temperature pyrolysis, the SiZrBOC precursor was transformed into a crystalline ceramic material with a yield of 89.5 wt%. Fourier infrared spectroscopy (FT-IR) and thermogravimetric analysis (TGA) were applied to characterize the polymer-ceramic conversion process and thermal behavior of ceramic precursors. According to the results, the addition of boron elements led to the formation of Si-O-B links in the system. X-ray diffraction (XRD) and transmission electron microscopy (TEM) were used to study the phase composition and microstructure of SiZrBOC ceramics. Finally, the oxidation test at 1200 °C revealed that SiZrBOC ceramics with a boron/zirconium molar ratio of 2.5:1 exhibited the best oxidation resistance at a weight gain of 0.4 wt% only.     

Layered double (Ni,Fe) hydroxide grown on nickel foam and modified by nickel carbonyl powder and carbon black as an efficient electrode for water splitting

Developing novel oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) catalysts is vital for water splitting. Here, carbon black (CB) and nickel carbonyl powder (NCP) are used as components, and the nonionic surfactant polyvinyl pyrrolidone (PVP) is used as a shape-controlled capping agent to easily prepare layered double (Ni, Fe) hydroxide (NiFe-LDH) electrodes. Scanning electron microscopy observation and X-ray photoelectron spectra analysis show that the Fe²⁺-doped layered double hydroxide is grown in situ on nickel foam (NF). CB (XC-72) and NCP further improve the electrical conductivity. At 10 mA?cm^?2, the overpotentials of the OER and HER are 203 mV and 83 mV, respectively, in 1 M KOH. Only 1.48 V is needed when both electrodes are applied for water splitting, and it has a stability of more than 100 h. This work can be used as a medium to elevate the OER and HER performance of NiFe-LDH-based catalysts.     

Kinetic Monte Carlo simulation of hydrogen production from photocatalytic water splitting in the presence of methanol by 1 wt% Au/TiO2

In this research, using the kinetic Monte Carlo simulation (KMC), the hydrogen production from a water-methanol mixture using Au/TiO₂ photocatalyst is investigated. A mechanism is proposed, and the rate constants of the reaction steps are specified. The reaction rate constants of different steps and the concentration of the active sites on the photocatalyst surface were determined. An excellent match between simulated and experimental data confirms the results. The electron-hole pair production, methanol adsorption on the photocatalyst surface, and electron-hole recombination steps are considered the most critical steps. To study the effects of independent variables (initial concentration of methanol, photocatalyst dosage, pH, and time of reaction) on the produced hydrogen, a combination of KMC simulation and design of experiment was employed. The concentration of photocatalysis has the highest and pH has the lowest effect on the hydrogen production. The optimal conditions for photocatalytic hydrogen production are presented.